HP Deskjet 6xx free download

File name ADJ6XX1.PDF

Adjustments HP DeskJet 6xx Printers Overview A properly adjusted mechanism provides optimum print quality without impacting the media handling capability of the printer. Print quality improves as the nozzles come closer to the paper. If the print cartridge is positioned too close to the media, however, the printer may experience paper jams, print skew, or print smear. Paper Guide - Fixed Carriage Rod - Adjustable at Each End 2162630 PPS - Pen to Pivot Spacing Pivot - Rotation Limit Determines PPS and Paper Guide to Pivot Gap Paper Guide to Pivot Gap Figure 1.Description of Adjustment Checks Adjustments - Overview 1. Checking the Pen-to-Pivot Spacing (PPS) The pen-to-pivot spacing (PPS) verifies the proper distance between the pen (PPS Measure Tool) and the pivot cockle ribs. The proper PPS distance is between 28 and 58 mils. The setting is impacted by the rotation limit of the pivot assembly and the height of the carriage rod. When adjustment is necessary, always try to pull the PPS into tolerance by first setting the pivot rotation limit using the pivot adjuster. If the spacing cannot be obtained by the pivot adjuster, then adjust the carriage rod by installing the carriage rod adjustment tools on both ends of the mechanism. 2168920 Figure 2. Adjusting the Pen-to-Pivot Spacing with the Pivot Adjuster Adjustments - Overview 2. Checking the Paper Guide-to-Pivot Gap With the pen-to-pivot spacing between 28 and 58 mils, check the paper guide-to-pivot gap. The paper guide-to-pivot gap determines the distance between the paper guide (which is fixed) and the pivot when in the normal printing position (printing on paper and transparencies). A shim is placed between the paper guide and the pivot. The difference between the reading on the Readout/Controller with the shim in place and removed should be between 15 and 35 mils. If the difference is less than 15 or greater than 35 mils, rotate the pivot adjuster to bring the difference between 15 and 35 mils. Note Adjusting the paper guide-to-pivot gap affects the pen-to-pivot spacing. Check the pen-to-pivot spacing after any paper guide-to-pivot gap adjustment. 2168905 Figure 3. Inserting the Shim Between the Paper Guide and the Pivot Adjustments - Overview 3. Adjustments - Overview 4.

File name ADJ6XX2.PDF

Adjustments HP DeskJet 6xx Printers Set Up and Calibrate the PPS Measure Tool and Readout/Controller Note The following calibration procedure verifies the PPS Measure Tool and Readout/Controller are operating properly. 1. Set the dip switches on the back of the Readout/Controller as shown below. CHANNEL Switches 2168602 2. Plug the PPS Measure Too into CHANNEL A on the back of the Readout/Controller. 3. Plug in the AC power cord. Allow the instrument to warm up for at least 10 minutes. Adjustments - Set Up and Calibrate the PPS Measure Tool and Readout/Controller 1. 4. On the Readout/Controller, press the MENU button. The Readout/Controller will display the message PASSWORD PLEASE. 5. Enter the password (press the , , and buttons). The Readout/Controller should display CAL SW DISABLED. 6. Press the CAL button. The Readout/Controller should display CAL SW ENABLED. PRE-SET Light CAL Light SP2 SP SP GO ZER CAL PRE PRE-SET Button CAL Button ZERO Button MENU 1.2345 MENU Button SEL RST 2168601 7. Using the MENU button, step through and verify all of the Readout/Controller settings. The table below identifies the Readout/Controller settings. Use the following procedure to change a Readout/Controller settings: · Press the PRE-SET button () to position the cursor over the digit. · Press the and buttons on the Readout/Controller to increase and decrease the setting value. · Once the desired setting is obtained, press the MENU button to retain the new setting and sequence to the next setting in the table. Adjustments - Set Up and Calibrate the PPS Measure Tool and Readout/Controller 2. 8. Continue to press the MENU button, sequencing through all of the Readout/Controller settings until the display reads DEPRESS MENU SWITCH TO RUN. Table 1. Readout/Controller Settings Selection DECIMAL PT CH(A) PRE-SET # CH(A) CAL # CH(A) FS # CH(A) SP1 TO MONITOR SP1 TO BE SET SP1 SP2 TO MONITOR SP2 TO BE SET SP2 SP3 TO MONITOR SP3 TO BE SET SP3 SP4 TO MONITOR SP4 TO BE SET SP4 SET LOW HYS SET HIGH HYS Setting 000.03 000.00 070.00 050.00 CH(A) LOW SETPOINT -001.00 CH(A) LOW SETPOINT 028.00 CH(A) HIGH SETPOINT 058.00 CH(A) HIGH SETPOINT 071.00 000.00 000.00 DEPRESS MENU SWITCH TO RUN Adjustments - Set Up and Calibrate the PPS Measure Tool and Readout/Controller 3. Adjustments - Set Up and Calibrate the PPS Measure Tool and Readout/Controller 4.

File name ADJ6XX3.PDF

Adjustments HP DeskJet 6xx Printers Checking the Pen-To-Pivot Spacing 1. If removed, install the PPS Measure Tool. Snap the PPS Measure Tool into the cradle, just like installing a black print cartridge. 2168906 2. Lift the envelope sensor on the mechanism to raise the pivot to its maximum height. 2168907 Note Make sure the envelope sensor remains raised during this entire procedure. Adjustments - Checking the Pen-To-Pivot Spacing 1. 3. Slide the black print cartridge cradle over the left paper feed roller. 2168910 4. Observe the Readout/Controller display reading. The reading should be between 028.00 and 058.00 mils. · If the measurement is within tolerance, continue on to the next step. · If the reading is less than 028.00 mils, rotate the pivot adjuster until the Readout/Controller displays a reading of 030.00 mils. If the reading cannot be increased to 030.00 mils, the carriage rod needs adjustment. · If the reading is greater than 058.00 mils, rotate the pivot adjuster until the Readout/ Controller displays a reading of 056.00 mils. If the reading cannot be decreased to 056.00 mils, the carriage rod needs adjustment. 2168909 Adjustments - Checking the Pen-To-Pivot Spacing 2. 5. Slide the black print cartridge cradle over the right paper feed roller. 2168911 6. Observe the Readout/Controller display reading. The reading should be between 028.00 and 058.00 mils, and roughly the same as step 4. · If the measurement is within tolerance, check the Paper Guide-to-Pivot Gap. · If the reading is less than 028.00 mils, rotate the pivot adjuster until the Readout/Controller displays a reading of 030.00 mils. If the reading cannot be increased to 030.00 mils, the carriage rod needs adjustment. · If the reading is greater than 058.00 mils, rotate the pivot adjuster until the Readout/ Controller displays a reading of 056.00 mils. If the reading cannot be decreased to 056.00 mils, the carriage rod needs adjustment. 2168909 Adjustments - Checking the Pen-To-Pivot Spacing 3. Adjustments - Checking the Pen-To-Pivot Spacing 4.

File name ADJ6XX4.PDF

Adjustments HP DeskJet 6xx Printers Checking the Paper Guide-To-Pivot Gap 1. Center the carriage between the right and center drive rollers. 2168904 2. If removed, install the PPS Measure Tool. Snap the PPS Measure Tool into the cradle, just like installing a print cartridge. 2168906 3. Lift the envelope sensor on the mechanism to raise the pivot to its maximum height. Adjustments - Checking the Paper Guide-To-Pivot Gap 1. 2168907 4. Observe the Readout/Controller reading with no shim on the paper guide. 5. Push down on the pivot, dropping the envelope sensor down onto the paper guide. 6. Place the adjustment shim on the pivot pad, located at the far right end of the pivot. 2168905 7. Lift the envelope sensor on the mechanism to raise the pivot to its maximum height. This will allow the pivot to release and capture the shim against the paper guide. Adjustments - Checking the Paper Guide-To-Pivot Gap 2. 2168907 8. Observe the Readout/Controller reading with the shim in place. 9. Determine the difference between the reading with the adjustment shim installed and removed from the mechanism. The difference between the readings should be between 015.00 and 035.00 mils. · If the Readout/Controller readings are within 015.00 and 035.00 mils of each other, remove the adjustment shim check the wiper height. · If a Readout/Controller reading is not within 015.00 and 035.00 mils of each other, the mechanism requires the paper guide-to-pivot gap adjustment. Remove the adjustment shim and adjust the paper guide-to-pivot gap. Adjustments - Checking the Paper Guide-To-Pivot Gap 3. Adjustments - Checking the Paper Guide-To-Pivot Gap 4.

File name ADJ6XX5.PDF

Adjustments HP DeskJet 6xx Printers Adjusting the Carriage Rod 1. Replace the right and left bracket screws (part number 0515-2522). Do not tighten the new screws. The washer, however, should just touch the bracket. Note: The screw/washer combination must be replaced with a larger washer to help ensure the old washer indentation does not affect the new adjustment. 2. Attach the right adjustment tool to the right end of the mechanism as follows: A. Align the fixed and spring loaded posts on the right adjustment tool with the two holes on the right side of the mechanism, just below the carriage rod tip. B. While pushing the spring loaded post, mount the right adjustment tool on the right side of the mechanism. Then release the spring loaded post. HP DeskJet 6xx Printers - Adjustments (Adjusting the Carriage Rod) 1 Note: You may need to turn the micrometer knob in order to have both posts (fixed and spring loaded) align with both holes on the side of the mechanism. Note: If the tool is properly mounted on the mechanism, the spring loaded post will remain depressed once you release the post. 3. Remove the rod retainer from the left end of the mechanism. Note: A misaligned adjustment tool could damage the mechanism. To avoid this, verify that the bracket screw on the left side is already loose. If not, loosen the screw now. 4. Attach the left adjustment tool to the left end of the mechanism as follows: A. Align the left adjustment tool over the left edge of the mechanism. B. Lower the left adjustment tool such that it straddles the left edge of the mechanism. HP DeskJet 6xx Printers - Adjustments (Adjusting the Carriage Rod) 2 Note: You may need to turn the micrometer knob in order to have the left adjustment tool fully seat on the left side of the mechanism. 5. Lock the left adjustment tool to the left side of the mechanism. 6. Install the LVDT. 7. Lift the envelope sensor on the mechanism to raise the pivot to its maximum height. HP DeskJet 6xx Printers - Adjustments (Adjusting the Carriage Rod) 3 Note: Make sure the envelope sensor remains raised during this entire procedure. 8. Slide the LVDT over the left paper feed roller. HP DeskJet 6xx Printers - Adjustments (Adjusting the Carriage Rod) 4 9. Adjust the left end of the carriage rod by turning the mircometer knob on the left adjustment tool. The Readout/Controller should display between 028.00 and 058.00 mils (nominally 040.00 mils). 10. Slide the LVDT over the right paper feed roller. 11. Adjust the right end of the carriage rod by turning the micrometer knob on the right adjustment tool. The Readout/Controller display should read between 028.00 and 058.00 mils (roughly the same as step 10). HP DeskJet 6xx Printers - Adjustments (Adjusting the Carriage Rod) 5 12. Move the carriage back over the left paper feed roller and readjust to the right paper feed roller setting (+2 mils). 13. Move the carriage back over the right paper feed roller and readjust to the left paper fe

File name ADJ6XX6.PDF

Adjustments HP DeskJet 6xx Printers Calibrating the Banner Printer Feature Ensure that the printer is connected to the computer's printer port (LPT1 or LPT2). 1. Turn on the printer. 2. Ensure the banner lever is set to the cut-sheet (left-most position). Note: The Banner Lever must be in the Cut-Sheet position before proceeding. Otherwise, the printer will become misaligned and banner paper will not be picked. 3. Press the "Run" button in the "Printer Utilities" section of the DeskJet Online Service Manual to send the banner calibration file to the printer. 4. Wait until the printer completes the calibration routine and prints the slightly modified Diagnostic Test. 5. Observe the Pen State value on the Diagnostic Test printout: Pen State: Steps to bump: xxx The number should fall within the range of 140 - 230. Troubleshooting 1. If the number is less than 140, verify that the banner lever is positioned all the way to the left. 2. If the number is greater than 230, verify that the pivot assembly is installed correctly in the printer. Other Methods of Sending the Calibration File to the Printer Note: The below examples assume the file "CAL.PCL" is on a disk in drive A:. From DOS Use the binary copy command to send the file to LPT1 or LPT2. For example, COPY /B A:\CAL.PCL LPT1 {Enter} From Windows 3.1 You may use the MS-DOS prompt and proceed as above, or select "File Manager," and select the A: drive, highlight CAL.PCL, select "File," then select "Copy." When prompted "Copy To:" enter LPT1 or LPT2, select "OK," then select "Yes." From Windows 95 Select "MS-DOS" prompt, from the "Programs" menu. Proceed as you would DOS (see above). HP DeskJet 6xx Printers - Calibration (Calibrating the Banner Printer Feature) 1

File name ADJ6XX7.PDF

Adjustments HP DeskJet 6xx Printers Verifying the Banner Printer Feature 1. Push and hold the Power button and press the Resume button five times to initiate the Diagnostic Test printout. 2. A number will appear on the Diagnostic Test printout next to the heading: Pen state: Steps to bump: xxx The number should fall within the range of: 140 - 230. Troubleshooting 1. If the number is less than 140, verify that the Banner Lever is positioned all the way to the left. 2. If the number is greater than 230, verify that the Pivot Assembly installed is correct for the printer. Optional Methods of Sending the Calibration File to the Printer In addition to being able to send the calibration file from the DeskJet Repair Reference, you can also send the file to the printer from a separate Banner Calibration disk. Use one of the following methods to send the Banner Calibration file from a disk. DOS: Use the binary copy command to send the file to LPT1 (or LPT2). For example: COPY/B A:\CAL.PCL LPT1 {Enter}. Windows 3.1: You may use the MS-DOS Prompt and proceed as above or: 1. Select "File Manager" 2. Select the A: drive 3. Highlight CAL.PCL, 4. Select "File," 5. Select "Copy." 6. When prompted "Copy To:," type: "LPT1" (or "LPT2") 7. Select "OK," then select "Yes." Windows 95: Select "MS-DOS Prompt" from the "Programs" menu. Proceed as you would in DOS (see above). HP DeskJet 6xx Printers - Adjustments (Verifying the Banner Printer Feature) 1